Innokin VCAP Replacement Pod

Innokin VCAP Pod

The Innokin VCAP replacement pod is a refillable 2ml pod cartridge with a built-in mesh coil, designed for use with the Innokin Trine, Trine SE, Endura V, Endura V Box, and Endura V Pro kits. Rather than swapping out a separate coil, you replace the whole pod when the coil is spent - quick, clean, and no cotton-touching required.

The pods are available in four resistances to suit different vaping styles, from a wide-open 0.4ohm direct-to-lung option right through to a tighter 1.2ohm mouth-to-lung pod. All four variants share the same 2ml capacity and top-fill design, and each is colour-coded so you can tell them apart at a glance.

Innokin VCAP Pod Key Features

• 2ml e-liquid capacity
• Built-in mesh coil - replace the pod, not just the coil
• Top-fill design, accessed by removing the mouthpiece
• Four resistances: 0.4ohm, 0.6ohm, 0.8ohm, and 1.2ohm
• Colour-coded by resistance
• Transparent pod body to monitor fill level
• Intelligent pod recognition on compatible devices
• Suits MTL, RDTL, and DTL vaping styles depending on variant
• Compatible with nic salt and 50/50 freebase e-liquids

Pod Variants

Four resistances are available, each colour-coded and suited to a different vaping style. Note that the 0.4ohm variant is not compatible with the original Innokin Trine - see the Compatibility section below for full details.

• 0.4ohm Mesh (Red) - 25 to 30W, direct-to-lung (DTL)
• 0.6ohm Mesh (Orange) - 20 to 22W, loose RDTL
• 0.8ohm Mesh (Blue) - 12 to 14W, loose-to-medium RDTL/MTL
• 1.2ohm Mesh (Green) - 11 to 12W, tighter MTL

Top-Fill Design

To refill a VCAP pod, simply pull the mouthpiece off the top of the pod - it exposes the fill port directly underneath. Fill with your chosen e-liquid, replace the mouthpiece, and you're done. There's no need to remove the pod from the device to refill, and the design is leak-resistant when the mouthpiece is seated correctly. The transparent body means you can see the fill level at a glance without having to pull the pod out to check.

Built-In Coil

Each VCAP pod has a mesh coil built into the pod body, so there's no separate coil to source, prime, or install. When the coil reaches the end of its life - you'll notice a drop in flavour or a slightly burnt taste - you swap the whole pod for a new one. All compatible Innokin devices include intelligent pod recognition, which automatically detects the resistance of the installed pod and adjusts the output accordingly, so there's nothing to set manually.

Compatibility

VCAP pods are compatible with the following Innokin devices. The 0.4ohm pod works with all kits listed except the original Trine - if you use a Trine (not Trine SE), stick to the 0.6ohm, 0.8ohm, or 1.2ohm variants.

• Innokin Trine - 0.6ohm, 0.8ohm, and 1.2ohm only
• Innokin Trine SE - all four resistances
• Innokin Endura V - all four resistances
• Innokin Endura V Box - all four resistances
• Innokin Endura V Pro - all four resistances

E-Liquid Guide

Innokin recommends 50/50 (PG/VG) e-liquids with VCAP pods, which includes most nic salts and standard freebase 10ml bottles. Thicker high-VG liquids are not advised as they can affect wicking performance in these pods. For the tighter-drawing 0.8ohm and 1.2ohm variants, nic salts at 10mg or 20mg work particularly well. The 0.6ohm and 0.4ohm variants suit freebase e-liquids if you prefer a more open draw, though nic salts can still be used at lower strengths.

What's in the Box

• 1 x Innokin VCAP Replacement Pod (resistance of choice)