Vaporesso Vibe Replacement Pods

Vaporesso Vibe Pods

The Vaporesso Vibe replacement pods are the official refillable cartridges for the Vibe, Vibe SE, Vibe Nano and Vibe Nano Pro pod kits. Each pod contains two built-in dual mesh coils at different resistances, with the device automatically selecting the correct one based on the output mode in use. This means a single pod delivers both a tighter MTL draw in ECO mode and a slightly looser RDTL inhale in PWR mode without any manual changes.

Pods hold 2ml of e-liquid in line with UK TPD regulations and refill via a side port sealed with a silicone stopper. They are sold in packs of two and are available in two resistance pairings to suit different vaping preferences.

Vaporesso Vibe Replacement Pods Key Features

• 2ml side-fill pod with silicone stopper
• Dual mesh coils built into each pod
• Two resistance options: 0.6Ω/0.8Ω and 0.7Ω/1.0Ω
• ECO mode (14W) and PWR mode (24W) coil pairing
• Hyperflow wicking technology
• Compatible with Vibe, Vibe SE, Vibe Nano and Vibe Nano Pro
• Magnetic connection
• Sold in packs of 2

2ml Side-Fill Pod with Silicone Stopper

Each pod holds 2ml of e-liquid, the maximum capacity permitted under UK TPD regulations. To refill, remove the pod from the device, lift the silicone stopper on the side and fill slowly before pressing the stopper firmly back into place. The transparent body lets you see the remaining e-liquid level at a glance, so there are no unexpected dry hits.

Dual Mesh Coils Built Into Each Pod

Rather than a single coil, each Vibe pod houses two separate mesh coils at different resistances within the same cartridge. The device fires whichever coil corresponds to the active output mode, so one pod genuinely covers two vaping styles without swapping anything. When the coils are spent, you replace the whole pod rather than attempting to change individual coils.

Resistance Options: 0.6Ω/0.8Ω and 0.7Ω/1.0Ω

Two pod variants are available, and choosing the right one comes down to how warm and airy you prefer your vape. The 0.6Ω/0.8Ω pod is the standard option: ECO mode fires the 0.8Ω coil at 14W for a tight MTL draw, and PWR mode fires the 0.6Ω coil at 24W for a warmer, slightly airier RDTL inhale. The 0.7Ω/1.0Ω pod runs cooler across both modes, with ECO at 12W and PWR at 20W, and suits vapers who prefer a gentler output or are using higher-nicotine nic salts.

ECO Mode and PWR Mode Coil Pairing

The Vibe's two output modes each activate a different coil within the pod. In ECO mode, the higher-resistance coil fires at the lower wattage, producing a tighter, cooler draw that conserves both battery and e-liquid. Switching to PWR mode fires the lower-resistance coil at higher wattage, opening the airflow and increasing vapour production. Changing modes on the device is all that is needed to move between the two experiences.

Hyperflow Wicking Technology

Vaporesso's Hyperflow wicking system is designed to draw e-liquid to the mesh coils quickly and evenly. This reduces the risk of dry hits when the pod is running low and helps maintain consistent flavour from the first fill to the last. Under normal use, each pod is rated for approximately 30 refills before the coils begin to degrade.

Compatible Devices

These pods fit the following Vaporesso kits:

• Vaporesso Vibe
• Vaporesso Vibe SE
• Vaporesso Vibe Nano
• Vaporesso Vibe Nano Pro

Magnetic Connection

Pods connect to the device via a magnetic snap-fit that holds the pod firmly in place during use. There is no threading or clipping required; the pod simply drops in and locks. The connection also carries the electrical contact between the pod and the device, so a clean, secure fit is important for consistent firing.

E-Liquid Recommendations

Both pod variants perform well with 50/50 (50% VG / 50% PG) and high-PG nic salt e-liquids, which wick efficiently through the mesh at MTL wattages. Higher-VG shortfills are not recommended as the thicker liquid can struggle to saturate the coil at these lower output levels, increasing the risk of a burnt taste. If you are using a 20mg nic salt, the 0.7Ω/1.0Ω pod in ECO mode provides a smooth, lower-temperature draw that suits higher-nicotine liquids well.

How to Prime a New Pod

Before firing a new pod for the first time, fill it and leave it to stand for five to ten minutes. This allows the e-liquid to fully saturate the wicking material before heat is applied. Taking two or three short, gentle draws without activating the device can also help pull the liquid into the coil. Skipping this step is the most common cause of a dry or burnt hit on the first use.

What's in the Box

• 2x Vaporesso Vibe dual mesh replacement pods (2ml)

Select your preferred resistance pairing when adding to your basket.